125B · 3 knobs
CadmusDual Boost
Based on the ZVEX Super Duper
- Category
- Boost· Dual-stage boost
- Controls
- Gain A · Gain B · Volume
- Difficulty
- Easy
- Price
- $12.50in stock
From the vendor
A two-channel boost composed of identical MOSFET gain stages. The boosts can be cascaded in series or selected independently.
The Cadmus Dual Boost is based on the ZVEX Super Duper, which is two of their SHO boost circuits in series and independently switchable.
The SHO is an extremely simple MOSFET booster, small enough that even two of them together have fewer components than most single effects.
The Super Duper is similar in concept to the Box of Rock, which adds a 3rd SHO stage as well as a tone control. That effect is more of an overdrive while this is a two-stage clean boost, though with both stages engaged this one can get into clipping if desired.
The Cadmus is a direct clone of the Super Duper with no added features other than pull-down resistors on each input to help prevent popping.
Note that since the channels are identical to individual SHO circuits, the two gain controls exhibit the characteristic “crackle” of the SHO when they are adjusted, since they are directly biasing the MOSFETs. This is normal.
Schematic
The schematic is in the vendor's build document, page 5. Open the build document. No KiCad fragment has been drawn for this circuit yet.
Parts list 33 rows
Report a wrong parse| Ref | Value | Normalized | Type | Notes |
|---|---|---|---|---|
| Resistors 12 | ||||
| R1 | 10M | 10M | Metal film resistor, 1/4W | |
| R2 | 10M | 10M | Metal film resistor, 1/4W | |
| R3 | 5k1 | 5.1k | Metal film resistor, 1/4W | |
| R4 | 100k | 100k | Metal film resistor, 1/4W | |
| R5 | 10M | 10M | Metal film resistor, 1/4W | |
| R6 | 10M | 10M | Metal film resistor, 1/4W | |
| R7 | 5k1 | 5.1k | Metal film resistor, 1/4W | |
| R8 | 100R | 100 | Metal film resistor, 1/4W | Power supply filter resistor. Labeled R23 in original release. |
| RPDA | 2M2 | 2.2M | Metal film resistor, 1/4W | Ch. A pull-down resistor. Can be as low as 1M. |
| RPDB | 2M2 | 2.2M | Metal film resistor, 1/4W | Ch. B pull-down resistor. Can be as low as 1M. |
| LEDA | 10k | 10k | Metal film resistor, 1/4W | Ch. A LED resistor. Adjust value to change LED brightness. |
| LEDB | 10k | 10k | Metal film resistor, 1/4W | Ch. B LED resistor. Adjust value to change LED brightness. |
| Capacitors 6 | ||||
| C1 | 100n | 100n | Film capacitor, 7.2 x 2.5mm | |
| C2 | 10uF | 10u | Electrolytic capacitor, 5mm | |
| C3 | 100n | 100n | Film capacitor, 7.2 x 2.5mm | |
| C4 | 10uF | 10u | Electrolytic capacitor, 5mm | |
| C5 | 100uF | 100u | Electrolytic capacitor, 6.3mm | Power supply filter capacitor. Labeled C17 in original release. |
| C6 | 100n | 100n | MLCC capacitor, X7R | Power supply filter capacitor. Labeled C18 in original release. |
| Diodes 3 | ||||
| D1 | 1N5817 | 1N5817 | Schottky diode, DO-41 | |
| D2 | 1N5239B | 1N5239B | Zener diode, 9.1V, DO-35 | Can sub any 9.1V zener, such as 1N4739A. |
| D3 | 1N5239B | 1N5239B | Zener diode, 9.1V, DO-35 | Can sub any 9.1V zener, such as 1N4739A. |
| Transistors 2 | ||||
| Q1 | BS170 | BS170 | MOSFET, N-channel, TO-92 | Can sub 2N7000, but rotate 180 degrees. |
| Q2 | BS170 | BS170 | MOSFET, N-channel, TO-92 | Can sub 2N7000, but rotate 180 degrees. |
| Potentiometers 2 | ||||
| GAIN B | 5kC | C5k | 16mm right-angle PCB mount pot | |
| VOL. | 50kB | B50k | 16mm right-angle PCB mount pot | |
| Switches 2 | ||||
| A.FSW | 3PDT | 3PDT | Stomp switch, 3PDT | Available from Aion FX. |
| B.FSW | 3PDT | 3PDT | Stomp switch, 3PDT | Available from Aion FX. |
| LEDs 2 | ||||
| A.LED | 5mm | 5MM | LED, 5mm, red diffused | |
| B.LED | 5mm | 5MM | LED, 5mm, red diffused | |
| Jacks & sockets 3 | ||||
| IN | 1/4" mono | 1/4" MONO | 1/4" phone jack, closed frame | Switchcraft 111X or equivalent. |
| OUT | 1/4" mono | 1/4" MONO | 1/4" phone jack, closed frame | Switchcraft 111X or equivalent. |
| DC | 2.1mm | 2.1MM | DC jack, 2.1mm panel mount | Lumberg NEB/J 21 C or equivalent. |
| Hardware 1 | ||||
| ENC | 125B | 125B | Enclosure, die-cast aluminum | Can also use a Hammond 1590N1. |