125B · 3 knobs
AnomalyVintage Distortion
Based on the Crowther Hot Cake
- Category
- Distortion
- Controls
- Drive · Presence · Level
- Difficulty
- Easy
- Price
- $12.50in stock
From the vendor
An adaptation of a one of the original boutique overdrive/distortion pedals from the 1970s, notable for its method of overdriving an op-amp directly rather than using diodes for clipping.
The Anomaly Vintage Distortion is an adaptation of the Crowther Hot Cake, an overdrive pedal from New Zealand that dates back to 1976. While the Hot Cake has seen many revisions throughout its history, the Anomaly is based on the 2008 revision that includes internal switches for “Bluesberry” and “XLF” (extra low frequency) modes. This version was traced by Aion FX in 2020.
The Hot Cake is notable for its lack of clipping diodes, instead overdriving the TL071 chip directly. Because of this, at some settings (most noticeable at medium gain) there can be a slight “fizz” as the note decays. The Bluesberry mode helps reduce this somewhat, but it’s part of the character of the pedal.
An updated version of the Hot Cake was released in late 2020 and moves the switches to the outside of the enclosure, although according to the manufacturer’s description the “Cream” mode is not the same as the earlier “Bluesberry” mode.
The Anomaly is an identical reproduction of Hot Cake in effect mode, although the bypass mode is somewhat altered. The original Hot Cake uses a relay to disable the gain of the op-amp and deactivate other frequency-shaping filters, transforming it into a unity-gain op-amp buffer. While creative, this approach is overly complicated. The Anomaly converts it to a standard true-bypass configuration.
Schematic
The schematic is in the vendor's build document, page 6. Open the build document. No KiCad fragment has been drawn for this circuit yet.
Parts list 39 rows
Report a wrong parse| Ref | Value | Normalized | Type | Notes |
|---|---|---|---|---|
| Resistors 14 | ||||
| R1 | 1M | 1M | Metal film resistor, 1/4W | |
| R2 | 10k | 10k | Metal film resistor, 1/4W | |
| R3 | 100k | 100k | Metal film resistor, 1/4W | |
| R4 | 220R | 220 | Metal film resistor, 1/4W | |
| R5 | 10k | 10k | Metal film resistor, 1/4W | |
| R6 | 10k | 10k | Metal film resistor, 1/4W | |
| R7 | 1k | 1k | Metal film resistor, 1/4W | |
| R8 | 1k | 1k | Metal film resistor, 1/4W | |
| R9 | 82k | 82k | Metal film resistor, 1/4W | |
| R10 | 100k | 100k | Metal film resistor, 1/4W | |
| R11 | 220k | 220k | Metal film resistor, 1/4W | |
| R12 | 220R | 220 | Metal film resistor, 1/4W | |
| RPD | 2M2 | 2.2M | Metal film resistor, 1/4W | |
| LEDR | 10k | 10k | Metal film resistor, 1/4W | |
| Capacitors 9 | ||||
| C1 | 10n | 10n | Film capacitor, 7.2 x 2.5mm | |
| C2 | 10uF | 10u | Electrolytic capacitor, 5mm | |
| C6 | 22n | 22n | Film capacitor, 7.2 x 2.5mm | |
| C7 | 82n | 82n | Film capacitor, 7.2 x 2.5mm | |
| C8 | 47n | 47n | Film capacitor, 7.2 x 2.5mm | |
| C9 | 100n | 100n | Film capacitor, 7.2 x 2.5mm | |
| C10 | 47uF | 47u | Electrolytic capacitor, 5mm | |
| C11 | 100uF | 100u | Electrolytic capacitor, 6.3mm | |
| C12 | 100n | 100n | MLCC capacitor, X7R | |
| Diodes 3 | ||||
| D1 | 1N5817 | 1N5817 | Schottky diode, DO-41 | |
| Z1 | BZX85C10 | BZX85C10 | Zener diode, 10V, DO-41 | Can substitute 1N4740A. |
| Z2 | BZX79C2V7 | BZX79C2V7 | Zener diode, 2.7V, DO-41 | Must be a 0.5W zener. See build notes. |
| Transistors 1 | ||||
| Q1 | 2N3906 | 2N3906 | BJT transistor, PNP, TO-92 | Substitute; original uses BC557. |
| ICs 1 | ||||
| IC1 | TL071 | TL071 | Operational amplifier, DIP8 | |
| Potentiometers 3 | ||||
| DRIVE | 50kC | C50k | 16mm right-angle PCB mount pot | |
| PRES. | 50kB | B50k | 16mm right-angle PCB mount pot | |
| LEVEL | 50kA | A50k | 16mm right-angle PCB mount pot | |
| Switches 3 | ||||
| XLF | SPDT on-on | SPDT ON-ON | Toggle switch, SPDT on-on | |
| MODE | SPDT on-on | SPDT ON-ON | Toggle switch, SPDT on-on | |
| FSW | 3PDT | 3PDT | Stomp switch, 3PDT | Available from Aion FX. |
| Jacks & sockets 4 | ||||
| IC1-S | DIP-8 socket | DIP-8 SOCKET | IC socket, DIP-8 | |
| IN | 1/4" stereo | 1/4" STEREO | 1/4" phone jack, closed frame | Switchcraft 112BX or equivalent. |
| OUT | 1/4" mono | 1/4" MONO | 1/4" phone jack, closed frame | Switchcraft 111X or equivalent. |
| DC | 2.1mm | 2.1MM | DC jack, 2.1mm panel mount | Lumberg NEB/J 21 C or equivalent. |
| Hardware 1 | ||||
| ENC | 125B | 125B | Enclosure, die-cast aluminum | Can also use a Hammond 1590N1. |