125B · 6 knobs
GladiusDynamic Overdrive
Based on the King Tone Soloist· 2 other boards clone it
- Category
- Overdrive
- Controls
- Drive · Body · Tone · Volume · Warmth · Asymmetric
- Difficulty
- Easy
- Price
- $12.50in stock
From the vendor
A single-channel adaptation of side A of the popular Duellist dual pedal, based on a stripped-down Ibanez Tube Screamer with hot-rodded features.
The Gladius Dynamic Overdrive is based on the King Tone Soloist, traced by Aion FX in 2022. First released in 2020, the Soloist is side “A” (String-Singer) of the Duellist dual pedal.
It’s no secret that it’s based on the Tube Screamer, but its modifications are significant enough that depending on the control settings, it can either sound nothing like a TS or exactly like one.
However, the Soloist is not an exact copy of the circuit inside the Duellist. A “Body” potentiometer has been added, and the “Fat” toggle mode has been swapped for the new “Edge” mode. The internal DIP switch has been removed, so the “Warmth” and “Asymmetric” modes from the Duellist are not in this circuit.
The Gladius unifies these two circuits, adding the internal DIP switch from the Duellist so that the Warmth and Asymmetric modes are once again available. Otherwise, it’s a direct adaptation of the Soloist standalone pedal.
Note: This project uses a type of capacitor that has been temporarily discontinued by WIMA. Please see our news article about the issue and the substitution spreadsheet for project-specific recommendations. We are stocking a limited supply in the mean time. The build document has not yet been updated to reflect this.
Schematic
The schematic is in the vendor's build document, page 6. Open the build document. No KiCad fragment has been drawn for this circuit yet.
Parts list 44 rows
Report a wrong parse| Ref | Value | Normalized | Type | Notes |
|---|---|---|---|---|
| Resistors 15 | ||||
| R1 | 1M | 1M | Metal film resistor, 1/4W | |
| R2 | 47k | 47k | Metal film resistor, 1/4W | |
| R3 | 4k7 | 4.7k | Metal film resistor, 1/4W | |
| R4 | 1k2 | 1.2k | Metal film resistor, 1/4W | |
| R5 | 3k3 | 3.3k | Metal film resistor, 1/4W | |
| R6 | 4k7 | 4.7k | Metal film resistor, 1/4W | |
| R8 | 1k | 1k | Metal film resistor, 1/4W | |
| R9 | 10k | 10k | Metal film resistor, 1/4W | |
| R10 | 220R | 220 | Metal film resistor, 1/4W | |
| R11 | 1k | 1k | Metal film resistor, 1/4W | |
| R12 | 10k | 10k | Metal film resistor, 1/4W | |
| R13 | 10k | 10k | Metal film resistor, 1/4W | |
| R14 | 100R | 100 | Metal film resistor, 1/4W | Power supply filter resistor. |
| RPD | 2M2 | 2.2M | Metal film resistor, 1/4W | Input pulldown resistor. |
| LEDR | 4k7 | 4.7k | Metal film resistor, 1/4W | LED current-limiting resistor. Adjust value to change LED brightness. |
| Capacitors 11 | ||||
| C1 | 22n | 22n | Film capacitor, 7.2 x 2.5mm | |
| C2 | 47pF | 47p | MLCC capacitor, NP0/C0G | |
| C3 | 47n | 47n | Film capacitor, 7.2 x 2.5mm | |
| C4 | 100n | 100n | Film capacitor, 7.2 x 2.5mm | |
| C5 | 220n | 220n | Film capacitor, 7.2 x 2.5mm | |
| C6 | 220n | 220n | Film capacitor, 7.2 x 2.5mm | |
| C7 | 220n | 220n | Film capacitor, 7.2 x 2.5mm | |
| C8 | 1uF | 1u | Film capacitor, 7.2 x 3.5mm | |
| C9 | 100uF | 100u | Electrolytic capacitor, 6.3mm | Reference voltage filter capacitor. |
| C10 | 100uF | 100u | Electrolytic capacitor, 6.3mm | Power supply filter capacitor. |
| C11 | 100n | 100n | MLCC capacitor, X7R | Power supply filter capacitor. |
| Diodes 4 | ||||
| D1 | 1N5817 | 1N5817 | Schottky diode, DO-41 | |
| D2 | BAS33 | BAS33 | Switching diode, DO-35 | Original uses BA282 diodes. The BAS33 is the closest available diode |
| D3 | BAS33 | BAS33 | Switching diode, DO-35 | currently available. See build notes. |
| D4 | BAS33 | BAS33 | Switching diode, DO-35 | |
| ICs 2 | ||||
| IC1 | RC4558P | RC4558P | Operational amplifier, DIP8 | |
| CHAR. | 2-pos. DIP | 2-POS. DIP | DIP switch, 2-position | |
| Potentiometers 4 | ||||
| DRIVE | 1MA | A1M | 16mm right-angle PCB mount pot | |
| BODY | 150kC | C150k | 16mm right-angle PCB mount pot | Can also use 250kC with tapering resistor. See build notes. |
| TONE | 20kW | W20k | 16mm right-angle PCB mount pot | |
| LEVEL | 100kA | A100k | 16mm right-angle PCB mount pot | Original uses linear taper, but audio taper will provide better control. |
| Switches 2 | ||||
| STYLE | SPDT cntr. off | SPDT CNTR. OFF | Toggle switch, SPDT on-off-on | |
| FSW | 3PDT | 3PDT | Stomp switch, 3PDT | |
| LEDs 1 | ||||
| LED | 5mm | 5MM | LED, 5mm, red diffused | |
| Jacks & sockets 4 | ||||
| IC1-S | DIP-8 socket | DIP-8 SOCKET | IC socket, DIP-8 | |
| IN | 1/4" stereo | 1/4" STEREO | 1/4" phone jack, closed frame | Switchcraft 112BX or equivalent. |
| OUT | 1/4" mono | 1/4" MONO | 1/4" phone jack, closed frame | Switchcraft 111X or equivalent. |
| DC | 2.1mm | 2.1MM | DC jack, 2.1mm panel mount | Mouser 163-4302-E or equivalent. |
| Hardware 1 | ||||
| ENC | 125B | 125B | Enclosure, die-cast aluminum | Can also use a Hammond 1590N1. |
Other boards based on the King Tone Soloist
- King Solo PCB Guitar Mania · 125B · €8.90
- Lone King Overdrive PedalPCB · 125B · $8.00