125B · 4 knobs
AzimuthDynamic Overdrive
Based on the Hermida Zendrive
- Category
- Overdrive
- Controls
- Drive · Tone · Voice · Volume
- Difficulty
- Beginner
- Price
- $12.50in stock
From the vendor
The first overdrive that attempted to replicate the tone of the legendary Dumble amplifiers. A favorite of blues guitarists, and with its low parts count, a great project for beginners.
The Azimuth Dynamic Overdrive is a recreation of the Hermida Zendrive, first released in 2004 and taken over by Lovepedal in 2013. The circuit has changed very little since its inception, with the only major change being the op-amp which happened after Lovepedal took over.
The Zendrive can be seen as a stripped-down Tube Screamer. It starts with a standard Tube Screamer-style clipping section, followed by a variable R-C treble cut and a buffer. The bass is adjustable via the “Voice” control, which varies the corner frequency of the filter coming off the op-amp. This also has the side-effect that the available gain increases as the Voice control is turned up.
Despite the legendary stature of the Zendrive, the circuit has among the lowest parts count of any Aion FX project and is a very good starting point for new builders.
Schematic
The schematic is in the vendor's build document, page 5. Open the build document. No KiCad fragment has been drawn for this circuit yet.
Parts list 36 rows
Report a wrong parse| Ref | Value | Normalized | Type | Notes |
|---|---|---|---|---|
| Resistors 10 | ||||
| R1 | 470k | 470k | Metal film resistor, 1/4W | |
| R2 | 1k | 1k | Metal film resistor, 1/4W | |
| R3 | 1k | 1k | Metal film resistor, 1/4W | |
| R4 | 10k | 10k | Metal film resistor, 1/4W | |
| R5 | 1k | 1k | Metal film resistor, 1/4W | |
| R6 | 10k | 10k | Metal film resistor, 1/4W | |
| R7 | 10k | 10k | Metal film resistor, 1/4W | |
| R8 | 100R | 100 | Metal film resistor, 1/4W | |
| RPD | 2M2 | 2.2M | Metal film resistor, 1/4W | |
| LEDR | 10k | 10k | Metal film resistor, 1/4W | |
| Capacitors 8 | ||||
| C1 | 470n | 470n | Film capacitor, 7.2 x 3.5mm | |
| C2 | 100pF | 100p | MLCC capacitor, NP0/C0G | |
| C3 | 100n | 100n | Film capacitor, 7.2 x 2.5mm | |
| C4 | 3n3 | 3.3n | Film capacitor, 7.2 x 2.5mm | |
| C5 | 470n | 470n | Film capacitor, 7.2 x 3.5mm | |
| C6 | 100uF | 100u | Electrolytic capacitor, 6.3mm | |
| C7 | 47uF | 47u | Electrolytic capacitor, 5mm | |
| C8 | 100n | 100n | MLCC capacitor, X7R | |
| Diodes 4 | ||||
| D1 | 1N5817 | 1N5817 | Schottky diode, DO-41 | |
| D2 | BAT41 | BAT41 | Schottky diode, DO-35 | |
| D3 | BAT41 | BAT41 | Schottky diode, DO-35 | Some versions of the Zendrive use a 1N34A germanium diode here. |
| D4 | BAT41 | BAT41 | Schottky diode, DO-35 | |
| Transistors 2 | ||||
| Q1 | 2N7000 | 2N7000 | MOSFET, N-channel, TO-92 | |
| Q2 | 2N7000 | 2N7000 | MOSFET, N-channel, TO-92 | |
| ICs 1 | ||||
| IC1 | NE5532P | NE5532P | Operational amplifier, DIP8 | |
| Potentiometers 4 | ||||
| GAIN | 500kA | A500k | Potentiometer, 16mm right-angle | |
| TONE | 50kB | B50k | Potentiometer, 16mm right-angle | |
| VOICE | 10kB | B10k | Potentiometer, 16mm right-angle | |
| VOL. | 100kB | B100k | Potentiometer, 16mm right-angle | |
| Switches 1 | ||||
| FSW | 3PDT | 3PDT | Stomp switch, 3PDT | Available from Aion FX. |
| LEDs 1 | ||||
| LED | 5mm | 5MM | LED, 5mm | |
| Jacks & sockets 3 | ||||
| IN | 1/4" stereo | 1/4" STEREO | 1/4" phone jack, closed frame | Switchcraft 112BX or equivalent. |
| OUT | 1/4" mono | 1/4" MONO | 1/4" phone jack, closed frame | Switchcraft 111X or equivalent. |
| DC | 2.1mm | 2.1MM | DC jack, 2.1mm panel mount | Lumberg NEB/J 21 C or equivalent. |
| Hardware 2 | ||||
| BATT | Battery snap | BATTERY SNAP | 9V battery snap | Optional. Use the soft plastic type—the hard-shell type will not fit. |
| ENC | 125B | 125B | Enclosure, die-cast aluminum | Can also use a Hammond 1590N1. |