Parts · ICs
NJM5532DD
1 circuit uses this part.
Substitutes same socket
Parts that fit the same socket: the same function, pin count and pinout. The figures are read off each part's datasheet (this one's from page 5), typical where the sheet gives a typical value, otherwise the maximum. Closest first; the last column says what differs. A different part can change the sound, and a circuit may lean on one particular figure, so read the build document's notes before you swap.
This part
| Part | Input | Supply | GBW | Slew | Noise | Iq | Boards |
|---|---|---|---|---|---|---|---|
| NE5532 | bipolar | 10–30 V | 12 MHz | 5 V/µs | 5 nV | 3 mA | 155 |
Low noise and strong output drive, but draws about 3 mA per amplifier and has 200 nA bias current.
Fits the same socket
| Part | Input | Supply | GBW | Slew | Noise | Iq | Boards | Differs |
|---|---|---|---|---|---|---|---|---|
| 4580 | bipolar | 4–36 V | 15 MHz | 5 V/µs | 3 mA | 103 | Low-noise, high-output-current audio dual from ±2 V; the DIP8 (NJM4580D) is listed as discontinued. | |
| NJM2100 | bipolar | 2–7 V | 12 MHz | 4 V/µs | 1.75 mA | 1 | 7 V max, not for 18 V. Low-voltage dual op-amp rated to ±3.5 V (7 V total), so it cannot run straight from 9 V. | |
| NJM4565D | bipolar | 8–36 V | 10 MHz | 4 V/µs | 2.25 mA | 2 | Drives 20 V peak-to-peak into 400 Ω; the DIP8 (NJM4565D) is listed as discontinued. | |
| UPC4570 | bipolar | 8–32 V | 15 MHz | 7 V/µs | 2.5 mA | 5 | Low-noise, wideband audio dual; needs at least ±4 V (8 V) supply. | |
| LM833 | bipolar | 10–36 V | 16 MHz | 7 V/µs | 4.5 nV | 2.05 mA | 144 | Low-noise audio dual; needs at least ±5 V (10 V) and draws about 2 mA per amplifier. |
| M5216 | 4–32 V | 10 MHz | 3 V/µs | 2.25 mA | 4 | High-current dual (±100 mA load) meant for headphone drivers. | ||
| 4559 | bipolar | ?–36 V | 4 MHz | 2 V/µs | 1.65 mA | 29 | Audio dual with stronger output drive than a 4558 (±10 V into 600 Ω). | |
| M5218 | 4–32 V | 7 MHz | 3 V/µs | 1.5 mA | 21 | Low-noise audio dual the maker calls close to the 4558 and 4559, with ±50 mA load current. | ||
| 4558 | bipolar | 10–30 V | 4 MHz | 2.2 V/µs | 7 nV | 1.25 mA | 1164 | Bipolar input with about 80 nA bias current, so it needs a DC bias path on each input. |
| OPA1678 | RR out | 4.5–36 V | 16 MHz | 9 V/µs | 4.5 nV | 2 mA | 6 | rail-to-rail output. Surface-mount only (SOIC-8 and smaller), so a DIP socket needs an adapter; standard dual pinout. |
| Faceplate | Circuit | Based on | Category | Vendor | Box | Knobs | Price | BOM |
|---|---|---|---|---|---|---|---|---|
| Cranetortoise HM-1 Distortion Vero21×20 Unverified 2N3904 · J201 · NJM5532DD Cranetortoise HM-1 Distortion | Cranetortoise HM-1 Distortion | Distortion | Dirtbox Layouts | — | 2 | — | 37 |