Akashic Guitar effects circuit lookup

Parts · ICs

MC33178P

Dual BJT-Input Op-Amp DIP-8.8 circuits use this part. Listed as: IC MC33178P.

Datasheet · from onsemi.com

Substitutes same socket

Parts that fit the same socket: the same function, pin count and pinout. The figures are read off each part's datasheet (this one's from page 4), typical where the sheet gives a typical value, otherwise the maximum. Closest first; the last column says what differs. A different part can change the sound, and a circuit may lean on one particular figure, so read the build document's notes before you swap.

This part

PartInputSupplyGBWSlewNoiseIqBoards
MC33178bipolar4–36 V5 MHz2 V/µs7.5 nV0.42 mA35

Low-noise bipolar dual that draws only about 0.42 mA per amplifier and drives 600 ohm loads.

Fits the same socket

PartInputSupplyGBWSlewNoiseIqBoardsDiffers
4559bipolar?–36 V4 MHz2 V/µs1.65 mA29draws 1.65 mA per amplifier. Audio dual with stronger output drive than a 4558 (±10 V into 600 Ω).
4558bipolar10–30 V4 MHz2.2 V/µs7 nV1.25 mA1164rated from 10 V; draws 1.25 mA per amplifier. Bipolar input with about 80 nA bias current, so it needs a DC bias path on each input.
NJM4565Dbipolar8–36 V10 MHz4 V/µs2.25 mA2draws 2.25 mA per amplifier. Drives 20 V peak-to-peak into 400 Ω; the DIP8 (NJM4565D) is listed as discontinued.
NJM2100bipolar2–7 V12 MHz4 V/µs1.75 mA17 V max, not for 18 V; draws 1.75 mA per amplifier. Low-voltage dual op-amp rated to ±3.5 V (7 V total), so it cannot run straight from 9 V.
M52184–32 V7 MHz3 V/µs1.5 mA21draws 1.5 mA per amplifier. Low-noise audio dual the maker calls close to the 4558 and 4559, with ±50 mA load current.
NE5532bipolar10–30 V12 MHz5 V/µs5 nV3 mA155rated from 10 V; draws 3 mA per amplifier. Low noise and strong output drive, but draws about 3 mA per amplifier and has 200 nA bias current.
4580bipolar4–36 V15 MHz5 V/µs3 mA103draws 3 mA per amplifier. Low-noise, high-output-current audio dual from ±2 V; the DIP8 (NJM4580D) is listed as discontinued.
M52164–32 V10 MHz3 V/µs2.25 mA4draws 2.25 mA per amplifier. High-current dual (±100 mA load) meant for headphone drivers.
UPC4570bipolar8–32 V15 MHz7 V/µs2.5 mA5draws 2.5 mA per amplifier. Low-noise, wideband audio dual; needs at least ±4 V (8 V) supply.
LM833bipolar10–36 V16 MHz7 V/µs4.5 nV2.05 mA144rated from 10 V; draws 2.05 mA per amplifier. Low-noise audio dual; needs at least ±5 V (10 V) and draws about 2 mA per amplifier.
FaceplateCircuitBased onCategoryVendorBoxKnobsPriceBOM
MXR Distortion III Vero17×14 Verified MC33178P · MPSA14 MXR Distortion III MXR Distortion IIIDistortionDirtbox Layouts—3— 28
MXR Distortion III Perfboard Unverified MC33178P · MPSA14 MXR Distortion III MXR Distortion IIIDistortionEffects Layouts (blog)—3— 29
Berzerk Overdrive MC33178P · MPSA14 MXR ZW-44 Zakk Wylde Overdrive · 1590B MXR ZW-44 Zakk Wylde OverdriveOverdriveHotKits1590B3$2.00 24
Custom Badass Modified OD 2N5088 · MC33178P · MPSA14 MXR Custom Badass Modified OD MXR Custom Badass Modified ODOverdrivePCBWay: Glory to Ukraine—3— 35
MXR Custom Badass Modified OD 2N5088 · MC33178P · MPSA14 —OverdrivePCBWay: Glory to Ukraine——— 50
MXR Distortion III Vero20×13 Verified MC33178P · MPSA14 MXR Distortion III MXR Distortion IIIDistortionTagboard Effects—3— 30
MXR GT-OD Vero20×12 Verified MC33178P · MPSA14 MXR GT-OD MXR GT-ODDistortionTagboard Effects—3— 24
MXR ZW44 Zakk Wylde Vero19×12 Verified MC33178P · MPSA14 MXR ZW-44 Zakk Wylde Overdrive MXR ZW-44 Zakk Wylde OverdriveDistortionTagboard Effects—3— 23