125B · 5 knobs
ThulcandraBoost / Overdrive
Based on the Xotic Soul Driven· 2 other boards clone it
- Category
- Overdrive· Boost / Overdrive
- Controls
- Gain · Treble · Bass · Mid Boost · Volume
- Difficulty
- Easy
- Price
- $12.50in stock
From the vendor
A mid-gain overdrive with three different tone controls to fine-tune the character. Developed in collaboration with Allen Hinds.
The Thulcandra Boost/Overdrive is an adaptation of the Xotic Soul Driven, a cousin of the classic AC Booster with roots in the Tube Screamer family, originally released in collaboration with Allen Hinds. This is an original trace by Aion FX.
The Soul Driven replaces the tone section of the AC/RC Booster circuit with a gyrator-based bass boost stage that emphasizes the 125Hz frequency. Using internal DIP switches, four bass boost settings are available: flat, +2.4dB, +3.6dB and +6dB.
The “Mid Boost” control is similar to the Zendrive‘s Voice control or the Timmy’s Bass knob, varying the resistor in the R-C filter to ground from the op-amp clipping stage. This has the effect of raising or lowering the bass cutoff frequency as well as changing the overall gain ratio.
The Thulcandra project is faithful to the original, with the exception that the DIP switch has been replaced by a potentiometer to allow fine control over the amount of bass. (The DIP switch just selects between four pre-set resistor values, and it’s likely due to space considerations that they made it an internal control rather than an external potentiometer.)
Schematic
The schematic is in the vendor's build document, page 5. Open the build document. No KiCad fragment has been drawn for this circuit yet.
Parts list 54 rows
Report a wrong parse| Ref | Value | Normalized | Type | Notes |
|---|---|---|---|---|
| Resistors 17 | ||||
| R1 | 10k | 10k | Metal film resistor, 1/4W | |
| R2 | 1M | 1M | Metal film resistor, 1/4W | |
| R3 | 18k | 18k | Metal film resistor, 1/4W | |
| R4 | 1k8 | 1.8k | Metal film resistor, 1/4W | |
| R5 | 470k | 470k | Metal film resistor, 1/4W | |
| R6 | 18k | 18k | Metal film resistor, 1/4W | |
| R7 | 1k2 | 1.2k | Metal film resistor, 1/4W | |
| R8 | 10k | 10k | Metal film resistor, 1/4W | |
| R9 | 470k | 470k | Metal film resistor, 1/4W | |
| R10 | 100k | 100k | Metal film resistor, 1/4W | |
| R11 | 10k | 10k | Metal film resistor, 1/4W | |
| R12 | 470R | 470 | Metal film resistor, 1/4W | |
| R13 | 100k | 100k | Metal film resistor, 1/4W | |
| R14 | 22k | 22k | Metal film resistor, 1/4W | |
| R15 | 22k | 22k | Metal film resistor, 1/4W | |
| RPD | 2M2 | 2.2M | Metal film resistor, 1/4W | Input pulldown resistor. |
| LEDR | 4k7 | 4.7k | Metal film resistor, 1/4W | LED current-limiting resistor. Adjust value to change LED brightness. |
| Capacitors 14 | ||||
| C1 | 470n | 470n | Film capacitor, 7.2 x 3mm | |
| C2 | 150pF | 150p | MLCC capacitor, NP0/C0G | |
| C3 | 100n | 100n | Film capacitor, 7.2 x 2.5mm | |
| C4 | 4u7 | 4.7u | Electrolytic capacitor, 5mm | Can also use polarized (oriented according to silkscreen). |
| C5 | 1n5 | 1.5n | Film capacitor, 7.2 x 2.5mm | |
| C6 | 100n | 100n | Film capacitor, 7.2 x 2.5mm | |
| C7 | 2n2 | 2.2n | Film capacitor, 7.2 x 2.5mm | |
| C8 | 56n | 56n | Film capacitor, 7.2 x 2.5mm | |
| C9 | 56n | 56n | Film capacitor, 7.2 x 2.5mm | |
| C10 | 10uF | 10u | Electrolytic capacitor, 5mm | Can also use polarized (oriented according to silkscreen). |
| C11 | 10uF | 10u | Electrolytic capacitor, 5mm | Can also use polarized (oriented according to silkscreen). |
| C12 | 100uF | 100u | Electrolytic capacitor, 6.3mm | Power supply filter capacitor. |
| C13 | 47uF | 47u | Electrolytic capacitor, 5mm | Reference voltage filter capacitor. |
| C14 | 100n | 100n | MLCC capacitor, X7R | Power supply filter capacitor. |
| Diodes 7 | ||||
| D1 | 1N5817 | 1N5817 | Schottky diode, DO-41 | |
| D2 | BAT46 | BAT46 | Schottky diode, DO-35 | |
| D3 | 1N914 | 1N914 | Fast-switching diode, DO-35 | |
| D4 | 1N914 | 1N914 | Fast-switching diode, DO-35 | |
| D5 | BAT46 | BAT46 | Schottky diode, DO-35 | |
| D6 | 1N914 | 1N914 | Fast-switching diode, DO-35 | |
| D7 | 1N914 | 1N914 | Fast-switching diode, DO-35 | |
| Transistors 2 | ||||
| Q1 | 2N5088 | 2N5088 | BJT transistor, NPN, TO-92 | Original part number is BC849C, SMD type. 2N5088 is an equivalent. |
| Q2 | 2N5088 | 2N5088 | BJT transistor, NPN, TO-92 | Original part number is BC849C, SMD type. 2N5088 is an equivalent. |
| ICs 1 | ||||
| IC1 | LM833 | LM833 | Operational amplifier, DIP8 | |
| Potentiometers 5 | ||||
| TREBLE | 250kB | B250k | 16mm right-angle PCB mount pot | |
| BASS | 25kB | B25k | 16mm right-angle PCB mount pot | |
| MID | 10kC | C10k | 16mm right-angle PCB mount pot | |
| GAIN | 1MB | B1M | 16mm right-angle PCB mount pot | |
| VOL | 100kB | B100k | 16mm right-angle PCB mount pot | |
| Switches 1 | ||||
| FSW | 3PDT | 3PDT | Stomp switch, 3PDT | |
| LEDs 1 | ||||
| LED | 5mm | 5MM | LED, 5mm, red diffused | |
| Jacks & sockets 4 | ||||
| IC1-S | DIP-8 socket | DIP-8 SOCKET | IC socket, DIP-8 | |
| IN | 1/4" stereo | 1/4" STEREO | 1/4" phone jack, closed frame | Switchcraft 112BX or equivalent. |
| OUT | 1/4" mono | 1/4" MONO | 1/4" phone jack, closed frame | Switchcraft 111X or equivalent. |
| DC | 2.1mm | 2.1MM | DC jack, 2.1mm panel mount | Mouser 163-4302-E or equivalent. |
| Hardware 2 | ||||
| BATT | Battery snap | BATTERY SNAP | 9V battery snap | Optional. Use the soft plastic type—the hard-shell type will not fit. |
| ENC | 125B | 125B | Enclosure, die-cast aluminum | Can also use a Hammond 1590N1. |
Other boards based on the Xotic Soul Driven
- Exotic Soul PCB Guitar Mania · 125B · €8.90
- Solenoid Overdrive PedalPCB · 125B · $8.00